All Products Minus B-Stock
-
$39.99
-
XS Power XS Power Li1208 12V 8A Lithium Charger
12 Volt Lithium Charger 8 Amps LED Charging & Status Indicators Microprocessor-Optimized Charging Constant Current/Constant Voltage Charger Auto Under-Voltage/10-Hour Shutoff Battery Reverse/Short Circuit/Overload Protection Integrated Cooling Fan This eight-amp IntelliCharger is equipped with an advanced microprocessor to quickly and safely recharge 12-volt lithium-ion batteries. The charger automatically measures progress to optimize charging performance, so you get the fastest charge possible without overcharging the battery. The integrated multicolor LEDs tell you when your battery is charging, and when it’s ready to go!See details below.High Frequency Lithium Battery IntelliCharger
$139.99
-
XS Power XS Power D1200 12 Volt AGM 2600 Amp Sealed Car Audio Battery/Power Cell+Terminal
12-Volt AGM Battery Max Amps: 2,600 Cold Cranking Amps: 651 Primary Watts: 1,500 Secondary Watts: 3,000 Reserve Capacity: 95 minutes M6 Terminal Hardware Incl. 3 Year Warranty 35.3 lbs. Measuring under eight cubic inches, the XS Power D1200 is the perfect solution for powering up your UTV as the main battery, while delivering all the juice you need to power 1,000 watts worth of accessories, like an audio system, an inverter or LED’s. You can also use the D1200 as a powerful 3,000-watt secondary battery for a larger audio system, winch, or when you want to run a power inverter for hours at a time. This compact battery delivers a ton of power quickly, making sure your ride is fully powered on the trails, dunes, or campsite! With its Absorbent Glass Mat (AGM) technology, the battery stays completely safe from spills, shock, and moisture, even in extreme heat or cold.
$259.99
-
Sundown Audio SFB-600D 600W Full Range Mono Amplifier
600 @ 1 ohms RMS 350 @ 2 ohms RMS 250 @ 4 ohms RMS Variable 12dB low pass filter: 80HZ – 20kHZ Variable 12dB high pass filter: 15HZ – 1kHZ Variable 12dB Bass Boost @ 50Hz 0-9dB Power, protection & clipping indicators included Thermal, voltage, speaker short, and dc-offset protection circuitry Wired remote control with clipping indicator The flexible SFB (Sundown Full Bridge) amplifiers pack a powerful punch in a compact size! Stable down to 1 ohm, the full-range SFB can be used as a subwoofer amp, or as an ideal power source for an array of P.A. speakers. If you are looking for raw power on a budget, look no further than the SFB Series from Sundown Audio.
$174.99
-
Sundown Audio Sundown Audio Nightshade NS-Series NS6 18" 3000W Subwoofer NS v.6
3500 Watt RMS / 7000 Watt Peak Dual 1 or 2 ohm voice coils Optional carbon cone/dustcap available Custom tooled basket Custom-tooled ultra-linear spider packs Extended shorting ring Eight-layer voice coil Custom tooled basket Cast aluminum cooling ring Ultra-linear spider pack Unique air exchanging system forces hot air out and cool air in Aluminum vent ring Ultra-linear Mega Roll V2 surround The Nightshade 3,000-watt Neodymium sub is engineered to deliver incredibly powerful low end, with an extremely linear excursion and next-level thermal management. It features an eight-layer voice coil for excellent power handling and an extended shorting ring to minimize distortion and deliver a smooth, highly accurate sound at extreme SPL levels.
$1,099.99
-
Mechman Alternators Mechman P101-L +1v Voltage Boost Harness
Description This voltage boost harness fits alternators with a GM 4 pin plug and is similar to our "plug and play" H104-L harness. The P101-L is the simplified version of the H104-L which makes it great for secondary alternator setups for a cleaner look or engine swap applications. The yellow wire gets connected to an ignition switched 12V+ source to turn the alternator on and off with ignition and the blue wire with ring terminal gets connected to the alternators threaded output stud. This harness can be used with engine swap applications where the stock alternator harness is not available, and you just need a way to turn the alternator on and off through a 12v switched connection.This harness may also be used WITHOUT THE BLUE WIRE CONNECTED as previously stated if you are currently running a regular battery but plan to upgrade later to a Lithium battery later in your build.
$29.00
-
Sundown Audio Sundown Audio SA-69CX 6"x9" Coaxial Speakers
125 W RMS Silk dome tweeter Hybrid fiber cone Integrated crossover Cast aluminum frame Premium spring-loaded speaker terminals SPL: 91 Db Frequency range: 45Hz - 20KHz Sundown’s premiere sound quality separates, the SA-6.5CS is a marvel of design and top-tier components. The midrange features a high-quality cast aluminum basket, housing a cone with a carefully selected blend of paper and wool fibers. This design dampens any unwanted resonances for an incredibly smooth, detailed response. The surround is a high-compliance rubber, engineered to tame edge resonances within the cone.An FEA-optimized motor was designed in-house and features a full 6mm one-way linear excursion - thanks to a carefully designed motor and extended pole piece. To increase thermal performance, the SA midrange features a vented magnetic gap and vented voice coil collar.The SA series silk dome tweeter matches the smooth sound of the midrange. After extensive testing, Sundown optimized the tweeter’s gap, dome material, lens, and chamber damping material. The results speak for themselves.The SA separates were engineered for one, simple goal: to let you completely immerse yourself in the music. At any volume. For as long as you want.
$259.99
-
ILL Customz ILL Customz Lug Style 4-Spot SAE Battery Terminals
ILL Customz SAE Battery Terminals are made for all batteries that have SAE Top post terminals. Whether your battery is stock or aftermarket, the Ill Customz SAE battery terminals are the perfect match. Great for marine, off-road, and audio use Comes in pairs (one positive, one negative) Made from Nickel Plated 6061 aluminum for added corrosion resistance and superior conductivity Lugs NOT INCLUDED ONLY WORKS WITH TAPERED SAE POST also known as top post Laser etched logo
$39.99
-
ILL Customz ILL Customz Input Style 6-Spot SAE Battery Terminals
ILL Customz SAE Battery Terminals are made for batteries that have SAE Top Post terminals. Whether your battery is stock or aftermarket, the Ill Customz SAE battery terminals are the perfect match. Great for marine, off-road, and audio use Comes in pairs (one positive, one negative) Made from Nickel Plated 6061 aluminum Works with 1/0AWG welding cable, 2/0AWG welding cable, and oversized 1/0AWG wire ONLY WORKS WITH TAPERED SAE POST (top post) Engraved logo
$44.99
-
Wet Sounds Wetsounds ST-ADP-RND 1.75 Stealth Clamp For 1.75" Round Pipe for Soundbar
Secure your Wet Sounds Soundbar in place when exploring the great outdoors with Stealth Brackets. CNC'd from billet aluminum, these round brackets will allow you to mount your Wet Sounds Sound Bar to your roll cage or tower tubing. Available in mulitple sizes to fit your need. If you have limited options on mounting, these can be used with the end legs of the soundbar (included with soundbar) or use with the Wet Sounds ST-ADP-SLIDER BRACKET.
$37.99
-
Sparked Innovations Sparked Single Red 12V Round LED Voltmeter-Lighter Size Car Audio/Racing
Universally use this 12VDC Voltmeter with LED display to monitor any 12volt application from marine to automotive dash panels. It’s similar in size to an automotive cigarette lighter mounting hole. IP67 waterproof rating allows it to be used on motorcycles or boats to monitor battery voltage. Circular housing makes it easy to mount. 12-Volt DC Voltmeter: RED LED Dual USB charge ports. 4.2A total for fast charge. Universal for any 12-volt project. Easily fits in dash panels. Similar in size to a cigarette lighter. Waterproofing allows it to be used on motorcycles or boats to monitor battery voltage. Circular housing makes it easy to mount. USB takes your 12v DC systems and converts it to 5v for USB charging. Comes with rubber cover for USB ports Specifications 5-15v DC operation range 3 digit digital display (Red) Anti-reverse, anti-short circuit protection ABS and nylon housing. Impact resistant and IP67 rated for water submersion up to 1 meter Operating temp -25~80C Accuracy class 0.1 Mounting hole diameter – 29.2mm Overall diameter – 36.5mm Mounting depth – 46mm including terminals Digit height – 6.5mm Showtime Electronics is an Authorized Sparked Innovations Dealer
$9.99
-
Kicker Kicker 46CXA360.4T 360W 90x4 Watt 4-Channel Car Audio Amplifier/Amp CXA360.4T CXA
CX360.4T 4-Channel Amplifier The CXA360.4T Four-Channel Amplifier is built to power all your door speakers in a single, powerful package. Flexible and Fun Using Class A/B power, this amp features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. A powerful 12dB crossover is also included, letting you quickly tune your system to perfection. CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time! Highly efficient heat sinks keep the amp cool with a sophisticated new look, while KICKER’s FIT+™ (Fail-safe Integration Technology-PLUS), gives you outstanding noise rejection - even with premium factory audio systems. This CX-Series Amplifier delivers as much as 90 watts into four full-range channels, or 180 watts into two bridged channels. See below for more details. Class A/B full-range channels Three-second turn-on/off delay to eliminate unwanted interference Variable 12dB crossovers provides control to dial in perfect sound KickEQ™ 6dB variable bass boost for those additional low frequencies FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio Accepts up to 40-volt input signal Small footprint for easier installation Vertical mounting hardware included for another unique look Compatible with CXARC Remote Bass Control Specifications MODEL CXA360.4 Power (watts/ch) 4 Ohm Stereo 65x4 Power (watts/ch) 2 Ohm Stereo 90x4 Power (watts/ch) 4 Ohm Mono 180x2 CXRC Remote Bass Capable (sold sep.) yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L) 12-1/2, 31.7 Frequency Response (Hz): 10Hz-20kHz Input Sensitivity: 250mV-10V (Low Level)1V-40V (High Level) Signal-to-Noise Ratio: 95dB Active Crossover: HI, LO or OFF; Variable 50–200Hz @ 12dB/Octave Subsonic Filter: n/a KickEQ™ Boost Variable 0-6dB @40Hz
$229.99
-
Kicker Kicker 43DSC6804 5x7/6x8 400 Watt 2-Way Coaxial Car Audio Speakers DS DSC68
DS Series 6x8" Coax A drop-in coaxial upgrade with the flexibility to fit nearly any vehicles doors for a vast improvement over factory sound. DS Series 6x8" Coax The DS 6x8-Inch Coaxial Speakers are the upgrade you need for great sound in your doors.A ribbed, UV-treated foam surround and rigid polypropylene cone with EVC™ (Extended Voice Coil) technology give you the best sonic quality and the deepest bass in a full range speaker.These DS speakers work best with 50 watts of recommended power. See below for more details. Specifications Model DSC680 Speaker Design 2 - Way Woofer [in, mm] 6x8, 160x200 Mid [in, mm] n/a Tweeter [in, mm] 1/2, 13 Rated Impedance [Ω] 4 Peak Power Handling [Watts] 200 Continuous Power Handling [Watts RMS] 50 Sensitivity [1W, 1m] 90 Frequency Response [Hz] 45-20k Mounting Hole Diameter [in, mm] 5x7 3/16, 126x182 Top Mount Depth [in, mm] 3/8, 9 Bottom Mount Depth [in, mm] 2-3/16, 56 Tweeter Protrusion [in, mm] 0 Grilles No Tweeter Magnet Material Neodymium Tweeter Dome Material PEI (polyether imide) Tweeter Design Balanced dome Woofer Cone Material Polypropylene Woofer Surround Material Polyester foam
$94.99 $84.99
-
Sundown Audio Sundown Audio U-Series v.1 12" Subwoofer
The Sundown U Series is our premier “standard suspension” woofer series. It is the most direct replacement for the world famous Z v.3 woofer line which we produced from 2011 to 2016 before launching the “new platform” Z v.4 series. Due to numerous advancements in our design process the U Series is able to deliver performance on-par with the Z v.3 series but at a much lower cost. We start with a double-stacked / 8.66” wide Y35 grade ferrite magnet system coupled to a one-piece, bumped T-Yoke and a 0.6” thick top-plate. Just as with the Z v.3 before it and our other high-end subwoofers we also add a very thick (5mm thickness) aluminum shorting ring inside the magnets to reduce static inductance and level out inductance over stroke. The U series motor also features a 0.6” long pole-extension to keep the coil under control at high levels of excursion. The voice coil is a 2.36” long / 3” diameter 4-layer aluminum winding / aluminum former unit – which is the same coil we use in our X v.2 series and, thus, the U series has the same 1500-watt RMS ratings. The coil temperature is kept in check by a heavily smoothed / high-velocity pole-vent and a series of ten direct air-gap vents in the back plate. The U series also features newly tooled cast aluminum vent rings in between the frame and top plate to effectively exchange air at a high velocity over the voice coil beneath the spider landing. The U series features an all-new cast aluminum frame series to the Sundown line which allows for taller cones than the older frames used on the Z v.3 series. The taller cones provide enhanced coil stability and increased mechanical excursion capability. We also tooled matching cast-aluminum surround clamps for the U series to ensure durability in the most demanding situations. The surrounds and cone bodies have been fully custom tooled especially for the U series and are stronger / support more excursion than the Z v.3 series cones and surrounds. The new cone bodies also feature an indentation for the same wide-flange, ultra-strong dust caps as our new platform subwoofers. If you are looking for a woofer that sounds similar to the SA series but handles significantly more power… the U series is exactly what you need. It has been designed to live up to the reputation earned by our Z v.3 series both in terms of every-day music enjoyment and SPL competition. Specifications Black Aluminum 3” voice coil former for superior heat dissipation High Temperature Round-Wire CCAW voice coil with high-temp black adhesive Double stitched surround Heavy duty cast basket Spring loaded terminals accept up to 8 gauge Stitched-on double-XL tinsel leads Rear vented pole piece Rear drilled gap-venting Innovative high-velocity cast aluminum vented frame spacer ring Magnet ID shorting ring Top-Plate Cooling Channels Cast Aluminum surround bolt-on rings Optimized for small ported or bandpass enclosures Specifications T/S SPECS U 12" D2 U 12" D4 RE (Ohms) 3.8 6.1 FS (Hz) 42.2 40.0 VAS (L) 17.9 12.3 Qes 0.30 0.38 Qms 2.67 2.93 Qts 0.27 0.34 Le (mH) 2.41 3.67 BL (NA) 31.2 33.7 Mms (Grams) 290.2 284.5 Cms (uM/N) 0.05 0.06 Sens (dB @ 1w/1m) 88.4db 85.0db Suggested SD-2 10" Sealed 0.5 ft^3 Ported 1.0 ft^3 Displacement 0.11 ft^3 Depth 4.75" Outside Diameter 10 1/2" Cut-Out 9 1/4" Recommended Tuning 32hz Recommended Port Area 16 in^2
$549.99 $349.99
-
XS Power XS Power Li1408 14V 8A Lithium Charger
14 Volt Lithium Battery Charger 8 Amps LED Charging & Status Indicators Microprocessor-Optimized Charging Constant Current/Constant Voltage Charger Auto Under-Voltage/10-Hour Shutoff Battery Reverse/Short Circuit/Overload Protection Integrated Cooling Fan This eight-amp IntelliCharger is equipped with an advanced microprocessor to quickly and safely recharge 14-volt lithium-ion batteries. The charger automatically measures progress to optimize charging performance, so you get the fastest charge possible without overcharging the battery. The integrated multicolor LEDs tell you when your battery is charging, and when it’s ready to go!See details below.High Frequency Lithium Battery IntelliCharger
$139.99
-
Sundown Audio Push Terminals
TERM-4G4AWG TERMINALTerminal - Standard 4awg, One woofer's worth (2 of each color)Zv.1, Zv.2, Zv.3NSv.1, NSv.2May Also be used on SA Classic to upgradeTERM-8SDTERMINAL FOR 8"Terminal - 8" Sundown, One woofer's worth (2 of each color)All 8" woofers excluding SMLTERM-BLOCKSUNDOWN TERMINAL BLOCKTerminal Block - Sundown, One woofer's worth10" - 18" WoofersUv.1, Uv.2Mv.1Xv.1, Xv.2, Xv.3, Xv.4Zv.4, Zv.5, Zv.6, Zv.7NSv.3, NSv.4, NSv.5, NSv.6SDDNTEAMMay Also be used on SAv.2 to upgradeTERM-SABLOCKSA SERIES TERMINAL BLOCKTerminal Black - SA, One woofer's worthSA ClassicSAv.2
$2.20 - $4.70
-
315 Custom Audio The Stubby
Bigger is not always better. Introducing the newest addition to our wood line The Stubby! Made in the USA with 100% baltic birch this will add some class to any audio build and be friendly to your wallet. As always we put our smooth responsive potentiometer in every knob with premium wiring and tiffany style rcas. cable length on bass knob is 24 inches and will provide decent length to plug in where needed. each knob is stained, built by hand, and tested to ensure your product is top quality. Please allow 5 to 7 business days to ship .Most orders are shipped ahead of schedule.
$64.99
-
Ampere Audio Ampere Audio AA-BI9 TL 6" x 9" 6x9 Car Speakers
100w 6x9" Coaxial Set When it comes to sound quality, the Ampere Audio AA-BI9 TL speakers are built from the ground up to be above par musical experiences. The wide frequency range delivers a pleasurable but aggressive Sound Quality Eargasm (SQE). The bass, midrange and treble all are very balanced giving you and all around excellent speaker. The AA-BI9 TL speakers are equipped with a silk dome tweeter which allows for smooth but strong high-frequency response. Additionally, the built-in crossover network streams audio frequencies to the proper driver – lows to the woofers, and highs to the tweeters so your music sounds like it’s coming from a live concert. Features 25mm Silk Dome Tweeter Fully Machined Hardened Plastic Tweeter Housing Dampened Pressed Paper Cone Smooth Termination Single Rubber Surround Powder Coated Aluminum Basket Custom Tooled Crossover with Direct Wiring Connections Audiophile 5 kHz Crossover with Tweeter Integrated Non Resonating Phase Plug Inter woven Tinsel Leads High Temperature CAE/CAD Motor Structure Specifications RMS Power: 100W Peak Power: 120W Nominal Impedance: 4 ohms Fs: 69 BL: 4.493 Qms: 3.5 Qes: 1.105 Qts: 0.840 SPL: 90.1 Vas: 22.113 Cms: 329.612 Mms: 16 Our Recommendation The Ampere Audio AA-BI9 TL is a perfect match for our class A/B AA-75.4 4-channel amplifier. Get them both to see what perfection sounds like!
$159.00 $59.99
-
$19.99
-
Sundown Audio Z-Series Drop-In Kit
**Zv1, Zv2 and Zv3 Drop-In Kits must be called in to order.**These are standard drop-in recone kits ONLY. If you need a custom recone kit, you will still need to call us to place your order.There are no refunds or exchanges with drop-in re-cone kits. Please make sure you are ordering the correct model, version and impedance prior to ordering.
$214.99 - $329.99
-
PRV Audio PRV Audio 6MB200-4 v2 6.5" 4-Ohm 200W Midbass Car Pro Audio Speaker MID
The PRV Pro Audio Loudspeaker, 6MB200 v2 mid bass woofer, offers outstanding durability and a smooth punch of mid bass for small enclosures. This woofer is perfect for home Hi-Fi installs, including bookshelf, satellite, surround sound speakers and even home studio monitors. The 6MB200-v2 now has more extended mid range response, up to 6.5 kHz compared to its previous model, and is a perfect option for mid range driver replacements in three-way cabinets. The magnet and motor assembly are attached to a sturdy reinforced steel frame, ensuring a solid support structure and long lasting play in most any environment. Its light weight of only 3.3 Lbs helps to keep your enclosures light, making it perfect for car audio applications. Highlights Nominal Impedance: 4 Ohms Rated AES Power Handling (RMS): 100 Watts Program Power: 200 Watts Sensitivity (1W/1m): 93.5 dB Voice Coil Diameter: 1.5″ GENERAL SPECIFICATIONS Nominal Diameter 6″ (152 mm) Nominal impedance 4 Ohms Rated AES Power Handling (RMS) 100 Watts Program Power 200 Watts Sensitivity 2.83V at 1m 93.5 dB Recommended Hi Pass Crossover****For Full Power Handling 125 Hz****12db Per Octave Crossover Frequency Response at -10dB 125 – 6,500 Hz Voice Coil Diameter 1.5″ (38 mm) Voice Coil Wire Copper Voice Coil Winding Depth 12.5 mm Former Material Kapton Magnetic Gap Depth 5.8 mm Frame Material Stamped Steel
$29.91
-
Sundown Audio Sundown Audio SALT-3 3000W Class D Amplifier
6,000 x 1 @ 2 ohms RMS (when linked) 3,000 x 1 @ 1 ohms RMS mono 1,500 x 1 @ 2 ohms RMS mono 750 x 1 @ 4 ohms RMS mono 24dB variable subsonic filter: 10HZ - 50HZ 24dB variable low pass filter: 35HZ - 250HZ Frequency Response : 10 Hz – 250 HZ Variable bass boost @ 45Hz 0-9dB Phase shift control 0-180 degrees Power, clipping and protection indicators included Thermal, voltage, speaker short, and dc-offset protection circuitry Included wired remote control displays voltage, temperature, and clipping Feel the power of the Sundown SALT-3! This strappable amp delivers a massive 6,000 watts at 2 ohms when attached to another SALT-3, or pump out 3,000 watts at 1 ohm on its own. The amp features both a 24dB variable subsonic and low pass filter, along with a bass boost at 45Hz, letting you dial in your personal, perfect sound. The phase shift control makes it easy to precisely adjust the output. With onboard indicators for power, clipping, and protection you’ll have full control over your setup. Use the included wired remote control to see voltage, temperature, and clipping at a glance.Producing optimum power at realistic voltages (the 12s, rather than needing 14+ volts), the SALT – Sundown Audio Low-Voltage Technology – is Sundown’s answer! SALT amplifiers represent the pinnacle of Korean Class-D amplifier technology. Whether you are a world-class SPL competitor or simply want to bang harder than absolutely anyone else, the SALT series will be right at home in your system. Specifications Input Sensitivity : 6V - 0.2V Efficiency : 90% < Signal / Noise Ratio : 90DB < Damping Factor : 400 < Tested Voltage & THD : 12.8V & Less Than 1% THD Operation Voltage : DC 9V - 15.5V Power Input Recommended Fuse : 300 Amps Dimensions : 19.68” L x 8.67” W x 2.80” H
$1,199.99
-
ILL Customz ILL Customz Single 4ga to 4ga Amplifier Inputs
These amp inputs will work with all amplifiers that come with 4ga terminals Single 4ga to 4ga single inputs will accept 4ga wire Made from Nickel Plated 6061 aluminum for added corrosion resistance Comes in pairs Comes with free red and black heat shrinks for positive and negative input
$17.99 $12.99
-
Clearance Deals Kenwood DPX524BT Double-DIN Bluetooth Receiver w/CD
KENWOOD DPX-524BT General Features: CD receiver with AM/FM tuner built-in MOSFET amplifier (22 watts RMS/50 peak x 4 channels) plays CDs, CD-Rs and CD-RWs, including discs loaded with MP3, WMA, and AAC files 13-digit variable-color display Smartphone Features: built-in Bluetooth for hands-free calling and audio streaming with dual phone connection supports Android music playback using the Kenwood Music Play app built-in iPhone and Android control using USB port Audio Features: 13-band parametric equalizer with 8 preset EQ curves subwoofer level controls high and low-pass filter controls bass boost and loudness controls Expandability: Music Drive lets you select audio from multiple flash drives or memory cards in a connected USB hub or memory card reader inputs: front panel auxiliary and USB inputs outputs: 3 SET outputs (2.5-volt front, rear, subwoofer) Other Info: compatible with most factory steering wheel audio controls (adapter required)
$209.99 $144.95
